View M62384FP08_4304258.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M62384FP
8-Bit, 4-Channel, 3 to 5 V D-A Converter (Buffered)
REJ03F0077-0200 Rev.2.00 Mar 25, 2008
Description
The M62384 is a CMOS-structure semiconductor integrated circuit incorporating four 8-bit D-A converter channels with output buffer op-amps. Serial data transfer type input can easily be used through a combination of three lines: DI, CLK, and LD. Outputs incorporate buffer op-amps that have a drive capacity of 1 mA or above for both sink and source, and can operate over the entire voltage range from almost ground to VCC (0 to 5 V), making peripheral elements unnecessary and enabling configuration of a system with few component parts. Support of power supply voltages of 3 V to 5 V enables the M62384 to be used in a wide range of applications.
Features
* 12-bit serial data input (3-line type: SDI, SCK, SLD) * Serial data transfer clock frequency: 10 MHz (max.) * Output buffer op-amps Operable over entire voltage range from almost ground to VCC * Power-on reset and external reset functions * Chip select function Up to 4 chips connectable on the same bus * Supported power supply voltage: 3 V to 5 V (2.7 V to 5.5 V)
Application
Signal gain setting and automatic adjustment in CTV and display monitors, conversion from digital data to analog data in consumer and industrial products
Pin Connection Diagram
M62384FP
GND 1 Ao1 Ao2 Vref Ao3 Ao4
2 3 16 CS1 15 CS0 14 RST 13 VDD 12 SCK 11 SDI 10 SLD 9
VCC 4
5 6 7
GND 8
VSS
(Top view) Outline: PRSP0016DE-A (16P2N-A)
This product is currently under development, and specifications and other details may be modified at a future date.
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 1 of 7
M62384FP
Block Diagram
SDI 11 SCK 12 VDD 13
12-bit shift register
RST 14
Power-on reset
8
Channel decoder
10 SLD 16 CS1 15 CS0
VSS 9
8-bit latch 8-bit D-A
8-bit latch 8-bit D-A
8-bit latch 8-bit D-A
8-bit latch 8-bit D-A
1 GND
Vref
5
VCC 4
2 Ao1
3 Ao2
6 Ao3
7 Ao4
Pin Functions
Pin No. 1, 8 2 3 6 7 4 5 9 10 Symbol GND Ao1 Ao2 Ao3 Ao4 Vcc Vref Vss SLD Function Analog GND: analog circuit GND (D-A converter lower reference voltage) D-A converter output pins (ch1 to ch4): full-swing buffer output Output voltage: Ao (00)h = 0V, Ao (FF)h = 255/256 x VREF
Analog power supply (3 V to 5 V) Must rise simultaneously with VDD or after VDD rise. D-A converter upper reference voltage input pin Digital GND Serial load signal input pin (Schmitt trigger input: with input hysteresis) When SLD is high, data is loaded from shift register into 8-bit latch corresponding to address. Serial data input pin (TTL input in case of 5 V power supply) Inputs serial data with a 12-bit data length (MSB-first). Serial clock signal input pin (Schmitt trigger input: with input hysteresis) At rising edge, data is read into shift register one bit at a time. Digital power supply pin (3 V to 5 V) When power supply rises, D-A output is reset (0 V output: power-on reset). Forced reset pin (TTL input in case of 5 V power supply) L: D-A output (AO1 to 4) = Fixed setting of 0 V H: Reset release (power-on reset operation) Chip select pins (TTL input in case of 5 V power supply) Access possible only when chip select data (D11, D10) and pin (CS1, CS0) logic match.
11 12 13 14
SDI SCK VDD RST
15 16
CS0 CS1
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 2 of 7
M62384FP
Absolute Maximum Ratings
(Unless specified otherwise, Ta = 25C)
Item Power supply voltage Digital input voltage Reference voltage input voltage D-A output voltage Permissible loss Operating ambient temperature Storage temperature Symbol VCC,VDD VDIN Vref VAO Pd Topr Tstg Rated Value -0.3 to 7.0 -0.3 to Vcc+0.3 ( 7.0) -0.3 to Vcc+0.3 ( 7.0) -0.3 to Vcc+0.3 ( 7.0) 300 -20 to +75 -40 to +125 Unit V V V V mW C C DC voltage ("H" level) Conditions
Recommended Operating Conditions
(Unless specified otherwise, VCC = VDD = 5 V 10%, Vref = 2 V to VCC, VSS = GND = 0 V, fsck = 5 MHz, VDINH = VDD, VDINL = VSS, Ta = 20C to 75C)
Specification Values Item Analog power supply voltage Digital power supply voltage Reference voltage Serial clock frequency "H" level digital input voltage "L" level digital input voltage Clock "H" pulse width Clock "L" pulse width Clock rise time Clock fall time Data setup time Data hold time Load setup time Load hold time Load "H" pulse width Reset "L" pulse width Load setup time after reset release Symbol VCC VDD Vref fsck VDINH VDINL tsckH tsckL tsckR tsckF tDCH tCHD tCHL tLDC tLDH tRSTL tRCHL Min. 2.7 2.7 2.0 0.5VDD VSS 30 30 Typ. Max. 5.5 5.5 5.5 10 VDD 0.2VDD Unit V V V MHz V V ns ns ns ns ns ns ns ns ns ns ns Test Conditions VCC = VDD VCC = VDD Vref VCC
VCC = VDD 2.7V VCC = VDD 2.7V
200 200 10 20 40 20 20 50 50
Timing Chart
tSCKR tSCKH t SCKF
SCK
tSCKL
SDI
t LDC t DCH t CHD t CHL t LDH
SLD
tRCHL t LDD
RST
t RSTL
AO
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 3 of 7
M62384FP
Electrical Characteristics
(Unless specified otherwise, VCC = VDD = 5 V 10%, Vref = 2 V to VCC, VSS = GND = 0 V, fsck = 5 MHz, VDINH = VDD, VDINL = VSS, Ta = 20C to 75C) (1) Digital block
Specification Values Item Digital block circuit current Input leakage current Input threshold voltage Input hysteresis voltage Symbol IDD IDINLK VDINT VDINT Min. -1.0 0.2VDD Typ. 0 100 Max. 1.0 1.0 0.5VDD Unit mA A V mV Test Conditions VDIN = VSS to VDD
(2) Analog block
Specification Values Item Analog block circuit current Reference voltage input current Differential nonlinearity error Nonlinearity error Zero scale error Full-scale error Output current Settling time Symbol ICC Iref SDL SNL SZERO SFULL IAO tLDD -1.0 -1.5 -2.0 -2.0 0.5 5 Min. Typ. 0.8 0.5 Max. 2.0 1.0 1.0 1.5 2.0 2.0 10 Unit mA mA LSB LSB LSB LSB mA S No load All channels: Maximum current conditions VCC = VDD = 2.7V to 5.5V IA0: With no load Test Conditions
VOA = 0.1V to VCC - 0.1V VOA = 0.54.5V, IOA = 0.1mA, Co = 50pF output absorbed within 0.5 LSB VCC = 0 V 5 V, V0A = 0 V setting voltage (reference values)
Power-on reset voltage
VPR
0.8
1.5
2.5
V
Digital Data Format
MSB(First) D11 D10 D9 D8 D7 D6 D5 D4 DAC data D3 D2 D1 LSB D0
Chip select data Address data
(1) Chip select data
D11 0 0 1 1 D10 0 1 0 1 CS1 L L H H CS0 L H L H
Data is transferred only when logic of D11 and D10 matches CS pin setting (CS1, CS0).
(2) Address data
D8 0 0 1 1 D9 0 1 0 1 Channel Selection AO1 selected AO2 selected AO3 selected AO4 selected
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 4 of 7
M62384FP DAC Data
D7 0 0 0 0 D6 0 0 0 0 D5 0 0 0 0 D4 0 0 0 0 D3 0 0 0 0 D2 0 0 0 0 D1 0 0 1 1 D0 0 1 0 1 D-A output (0/256)xVref (1/256)xVref (2/256)xVref (3/256)xVref

1 1
1 1
1 1
1 1
1 1
1 1
1 1
0 1
(254/256)xVref (255/256)xVref
Data Timing Chart
SDI D11 D10 D9 D8 D2 D1 D0
SCK
SLD
Ao When SLD is high, data captured in the shift register is loaded into the 8-bit latch corresponding to the address. Therefore, SCK should be held high or low when SLD is high.
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 5 of 7
M62384FP
Sample Application Circuit
SDI SCK MCU SLD RST
RST SLD SCK SDI
VCC VDD
VCC VDD Ao1 Ao2 Ao3
Vref
Chip select setting (connected to either VDD or GND)
Vref CS0 CS1 GND
Ao4
GND
VSS
M62384FP
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 6 of 7
M62384FP
Package Dimensions
JEITA Package Code P-SOP16-5.3x10.1-1.27 RENESAS Code PRSP0016DE-A Previous Code 16P2N-A MASS[Typ.] 0.2g
16
9
HE
*1
E
F
NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET.
1 Index mark
8 A2 A1
c
*2 D
Reference Dimension in Millimeters Symbol
e
y
*3
bp
Detail F
D E A2 A1 A bp c HE e y L
Min Nom Max 10.0 10.1 10.2 5.2 5.3 5.4 1.8 0.1 0.2 0 2.1 0.35 0.4 0.5 0.18 0.2 0.25 0 8 7.5 7.8 8.1 1.12 1.27 1.42 0.1 0.4 0.6 0.8
A
REJ03F0077-0200 Rev.2.00 Mar 25, 2008 Page 7 of 7
L
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries.
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
http://www.renesas.com
Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510
(c) 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.2

▲Up To Search▲

Price & Availability of M62384FP08

	To Download M62384FP08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .